$30.98
$38.73
Cost-effective economy oscilloscope, 150MHz Bandwidth, 1GSa/s, 8M memory depth; with 1CH 25MHz waveform generator, support arbitrary waveform output; 14 kinds of trigger modes, standard with 5 kinds of serial protocol triggers and decodes; 32 kinds of auto measurements with statistics; 3-digit digital voltage meter and 6-digit hardware frequency indicator functions; 2 sets of DVM; Abundant SCPI remote command control. It is a useful commissioning instrument for various fields such as communication, aerospace, national defense, embedded systems, computers, research and education. Model DSO2D15 DSO2D10 DSO2C15 DSO2C10 Bandwidth 150MHz 100MHz 150MHz 100MHz Oscilloscope channels 2CH 2CH 2CH 2CH Waveform generator 1CH 1CH - - Oscilloscope Sample rate 1GSa/s (single channel) 500MSa/s (two channels) Acquisition Normal Sample data Peak-to-peak value Display high frequency and random burr Average Average waveform, times: 4, 8, 16, 32, 64, 128 High resolution Up to 12bit Input Input coupling DC, AC, GND Input impedance 1MΩ±2% ‖20pF±3pF Probe attenuation factor 1X, 10X, 100X, 1000X Voltage rating 300V CAT II Maximum input voltage 300VRMS (10X) Horizontal Waveform interpolation (sin x)/x Maximum record length Single channel maximum 8M Two channels maximum 4M Horizontal scale range 2ns/div~100s/div 1, 2, 5 step by step Time base mode Y-T, X-Y, Roll Zero offset ±0.5 div×minimum time base gear Sample Rate and Delay Time Accuracy ±25ppm Delta Time Measurement Accuracy (Full Bandwidth)Sample Rate and Delay Time Accuracy single-shot, Normal mode ±（1 sample interval 100ppm×reading 0.6ns） ＞16 times averages ±（1 sample interval 100ppm×reading 0.4ns） Sample interval=sec/div÷200 Sample Rate and Delay Time Accuracy ±50ppm（at any interval greater than 1ms） Vertical Model DSO2D15 DSO2D10 DSO2C15 DSO2C10 Bandwidth 150MHz 100MHz 150MHz 100MHz Rising time in BNC position (typical) 2.4ns 3.5ns 2.4ns 3.5ns Vertical resolution 8 bits resolution, each channel samples simultaneously Vertical sensitivity 2mV/div to 10V/div Offset range ≥ 200mV/div, ±1V; ＜200mV/div ±50V Mathematical operation , -, ×, ÷, FFT FFT Window: Rectangle, Hanning, Hamming, Blackman, Bartlett, Flattop Bandwidth Limit 20MHz Bass response（-3db） In BNC position ≤ 10Hz Vertical gain accuracy In ''normal'' or ''average'' acquisition mode, the accuracy of 10V/div to 10mV/div is ±3%; In ''normal'' or ''average'' acquisition mode, the accuracy of 5mV/div to 2mV/div is ±4% Note: Bandwidth reduced to 6MHz when using a 1X probe Trigger Trigger type Edge, Pulse width, Video, Slope, Overtime, Window, Pattern, Interval, Under Amp, UART, LIN, CAN, SPI, IIC Trigger level range ±5 divisions from the center of the screen Trigger mode Auto, Normal, single Level CH1~CH2 ±4 divisions from the center of the screen EXT(Only With AWG Model) 0~3.3V Holdoff range 8ns~10s Trigger level accuracy CH1~CH2 0.2 div×volts/div within ±4 divisions from the center of the screen EXT(Only With AWG Model) ±（Set value× 6% 40mV） Edge trigger Slope Rising edge, falling edge, rising or falling edge Signal source CH1, CH2, EXT(Only With AWG Model) Pulse width trigger Polarity Positive polarity, negative polarity Condition(When) <, >, !=, = Signal source CH1~CH2, Pulse width range 8ns ~ 10s Accuracy 8ns Video trigger Signal standard NTSC, PAL Signal source CH1~CH2 Synchronization Scanning line, line number, odd field, even field, all field Slope trigger Slope rising, falling Condition(When) <, >, !=, = Signal source CH1 ~ CH2 Time range 8ns ~ 10s Accuracy 8ns Overtime trigger Signal source CH1~CH2， Polarity Positive polarity, negative polarity Time range 8ns ~ 10s Accuracy 8ns Window trigger Signal source CH1~CH2 Pattern trigger Pattern 0: low level; 1: high level; X: ignore Level（signal source） CH1~CH2 Interval trigger Slope rising, falling Condition(When) <, >, !=, = Signal source CH1~CH2 Time range 8ns ~ 10s Accuracy 8ns Under Amp trigger Polarity Positive polarity, negative polarity Condition(When) <, >, !=, = Signal source CH1~CH2 Time range 8ns ~ 10s Accuracy 8ns UART trigger Condition(When) Start, Stop, data, Parity ERR, COM ERR Signal source(RX/TX) CH1~CH2 Data format Hex (hexadecimal) Data length 1 byte Data bit width 5 bit, 6 bit, 7 bit, 8 bit Odd-even check none, odd, even Idle level high, low Baud rate (optional) 110/300/600/1200/2400/4800/9600/14400/19200/38400/57600/115200/230400/380400/460400 bit/s Baud rate(user-defined) 300bit/s~334000bit/s LIN trigger Condition(When) Interval field, synchronization field, ID field, synchronization error, identifier, ID and data Signal source CH1~CH2 Data format Hex (hexadecimal) Baud rate (optional) 110/300/600/1200/2400/4800/9600/14400/19200/38400/57600/115200/230400/380400/460400 bit/s Baud rate(user-defined) 300bit/s~334000bit/s CAN trigger Condition(When) Start bit, remote frame ID, data frame ID, frame ID, data frame data, error frame, all errors, ACK Error, overload frame Signal source CH1~CH2 Data format Hex (hexadecimal) Baud rate (optional) 10000, 20000, 33300, 500000, 62500, 83300, 100000, 125000, 250000, 500000, 800000, 1000000 Baud rate(user-defined) 5kbit/s~1Mbit/s SPI trigger Signal source CH1~CH2 Data format Hex (hexadecimal) Data bit width 4, 8, 16, 24, 32 IIC trigger Signal source (SDA/SCL) CH1~CH2 Data format Hex (hexadecimal) Data index 0~7 When(condition) Start bit, stop bit, No Ack, address, restart, address and data Measurement Cursor Voltage difference between cursors △V Time difference between cursors △T Reciprocal of △T, in Hertz (1/△T) Auto measurement frequency, period, mean, peak-to-peak, RMS, minimum, mixmum, rising time, falling time, width, - width, base, top, middle, amplitude, overshoot, preshoot, rising edge phase difference, falling edge phase difference, duty, - duty, period mean, PRMS, FOVshoot, ROVshoot, BWIDTH, FRF, FFR, LRR, LRF, LFR, LFF DVM Data source CH1, CH2 Measurement type DC RMS AC RMS DC Frequency meter hardware 6 bits frequency meter Arbitrary waveform generator Channel 1 Sample rate 200MSa/s Vertical resolution 12 bits Maximum frequency 25 MHz Standard waveforms sine, square, ramp,Exp, noise, DC Arbitrary waveform Arb1, Arb2, Arb3, Arb4 Sin Frequency range 0.1Hz~25MHz Square/pulse Frequency range 0.1Hz~10MHz Triangular wave Frequency range 0.1Hz~1MHz Sampling wave Frequency range 0.1Hz~1MHz Index Frequency range 0.1Hz~5MHz Noise Arb1 Frequency range 0.1 Hz to 10 MHz Arb2 Frequency range 0.1 Hz to 10 MHz Arb3 Frequency range 0.1 Hz to 10 MHz Arb4 Frequency range 0.1 Hz to 10 MHz Waveform length 4KSa Frequency Accuracy 100 ppm (<10 kHz) 50 ppm (>10 kHz) Resolution 0.1 Hz or 4 bits，take the greater one Amplitude Output range 10mV~7Vp-p (high impedance) 5mV~3.5Vp-p (50Ω) DC offset Range ±3.5 V, high impedance ±1.75 V, 50 Ω Resolution 100 μV or 3 bits, take the greater one Accuracy 2% (1 kHz) Output impedance 50 Ω General specifications Display Display type 7'' diagonal TFT liquid crystal Display resolution 800 (horizontal)*480 (vertical) pixels Display colour 16 million colours (24 bits true colour) Persistence time minimum, 1 s, 5 s, 10 s, 30 s, infinite Display type dot, vector Display brightness adjustable Grid type adjustable Grid brightness adjustable Interface Standard interface USB Host，USB Device General specifications Probe compensator output Output voltage, typical about 2Vpp input ≥1MΩ load Frequency, typical 1kHz Power supply 100-120VACRMS(±10%), 45Hzto 440Hz, CATⅡ 120-240VACRMS(±10%), 45Hz to 66Hz, CATⅡ Power consumption <30W Fuse T, 3.15A, 250V, 5x20mm Operating temperature 0~50 °C (32~122 °F) Storage temperature -40~ 71 °C (-40~159.8 °F) Humidity ≤ 104℉(≤ 40°C): ≤90% relative humidity 106℉~122℉ ( 41°C ~50°C): ≤60% relative humidity Altitude Operating and nonoperating 3, 000m (10, 000 feet) Mechanical shock Random vibration 0.31 g RMS from 50Hz to 500Hz, 10 minutes on each axis Nonoperating 2.46g RMS from 5Hz to 500Hz, 10 minutes on each axis Operating 50g, 11ms, half-sine wave Mechanical Size 318 x 110 x 150mm (length x width x height) Weight 1900g
Digital Ossilloscope
